Jul 12, 2016 Unboxing an original brick Gameboy DMG-01 with Tetris, link cable, headphones and extras. It was sold to me with the vertical line issue which I. May 20, 2014 When I bought this it wouldn't turn on at all. I took it apart, cleaned the battery contacts and cleaned inside and out and put it together and now it turns on. I tried heating and pressing the. Gameboy Zero Conductive Rubber Button Pads & 4 Buttons Nintendo Game Boy DMG-01 by ATomic Market. Livetype dmg. By Atomic Market. Get it as soon as Tue, Oct 1. FREE Shipping on orders over $25 shipped by Amazon. Only 3 left in stock - order soon.
- Gameboy Dmg-01 Games
- Gameboy Dmg-01 Replacement Screen
- Gameboy Dmg 01 Mod
- Gameboy Dmg-01 Lcd Screen
- Gameboy Dmg-01 1989
- 1Chip Info
- 2Game Boy DMG-01 Capacitor List
- 3Schematics
Chip Info
![Parts Parts](/uploads/1/3/4/3/134367015/960594533.jpg)
DMG-CPU-06
- U1: CPU: DMG-CPU
- U2, U3: RAM: LH5264TN-TL
- U4: DMG-AMP
Game Boy DMG-01 Capacitor List
https://qpuhuq.weebly.com/blog/download-music-for-mac. A quick note on replacing capacitors: there are a few caps on the LCD board that require removal of the LCD module to desolder. For those caps, I would not attempt to remove the LCD module, instead I would cut the leads as close to the old capacitor body as possible and solder the replacement parts to the old legs. The LCD modules are known for developing bad connections, so you probably don't want to aggravate the LCD during the capacitor replacement process.
DMG LCD-06
DMG-CPU-06
DMG JACK
DC CONV DMG
DC CONV2 DMG
Schematics
![Gameboy Gameboy](/uploads/1/3/4/3/134367015/525076631.jpg)
Drawn by Jeff Frohwein [1]
DMG-01 Schematics
- CPU Section
- LCD Section
- Power/Cartridge Section
Related Schematics
- 4 Player Adapter
- Super Game Boy SNES Cartridge
Retrieved from 'https://console5.com/techwiki/index.php?title=Game_Boy_DMG-01&oldid=4847'
I was inspired by the many Game Boy Zero builds on You Tube, but one in particular where the user used an original Game boy cart to house the micro SD card. I give the user props for a good functioning build, but with my ability to design PCBs and some more knowledge about getting hardware working I set out to build my own. My project is all working in prototype form except for the audio at this point because i didn't buy an audio amp board for prototyping.What I did is design a set of custom PCBs to replace the original GB PCBs and clean up the project significantly. Even though i was capable of designing the battery charger and audio amp circuits myself, I took the lazy route and leveraged some readily available designs from Adafruit and copied the Layout and schematics into my project.
Specs,
Original Game Boy DMG-01 Case.
Custom Main PCB
Custom Cart PCB
Gameboy Dmg-01 Games
Custom Button PCB with extra X - Y buttons.Adafruit 3.2' SPI TFT screen
Mono 2.5W amplifier Circuit
2000mA hour LiPo Battery
Battery Charger circuit
Main PCB
Holds the Pi Zero in a cut out in the middle of the board. Bridges the Connections over to the Cart header for the Mircro SD card. Also bridges the required pins from the GPIO to the screen header. Has Micro USB port for charging. Has USB-A port for external devices. Holds the battery charger circuit and audio amp circuit. I will be using the basic PWM out gpio pin for audio. the audio on these games are pretty crude anyways. The battery connector sticks through one of the openings in the battery compartment with some modification to the opening. I decided not to try to bring out the HDMI port as it would have been very complicated and using a SPI screen the output of the HDMI is the same very low resolution of the built in screen. I am also using the extra GPIO pins for the buttons instead of using a USB device like the teensy. this eliminates the need for a USB hub if you want a USB port on the outside.
Cart PCB
replaces the cart board with a custom board that holds the Micro SD card. Replaces the card edge connector with a female 0.1 pin header. I will post pictures of the board layout software, but the actual implementation will become more clear once I have the boards on monday.
Button PCB
There were existing options for the DMG-01, but they only had A and B buttons, I used the super game girl board at first for prototyping, but it wasnt really designed for the DMG GB even though it was based on the original 2 button PCB--ABXY button pads didn't line up. I decided to make my own board specifically for the DMG GB with the extra X and Y buttons. I am selling the extra boards on Ebay. I received them today and have pictures.
Gameboy Dmg-01 Replacement Screen
http://www.ebay.com/itm/231974209588?ss .. 1555.l2649Gameboy Dmg 01 Mod
Pictures and video.Video of GPIO mapped buttons and Adafruit screen working in Prototype form.
https://www.youtube.com/watch?v=GM_RlXi .. e=youtu.be
Main board and Cart board Panelized (Layout Software screen shot)
Gameboy Dmg-01 Lcd Screen
Button Board PCB